Hotspring Hot Tub How To Unlock

If you lot atomic number 82 a busy life or don't consider yourself mechanically inclined, y'all may be concerned that hot tub maintenance volition be difficult or counterbalance the stress relief a hot tub provides. Fortunately, regular HotSpring spa maintenance is quick and easy. In this web log we put together a guide for HotSpring Spas locks and troubleshooting, to make it fifty-fifty easier for you!

AUXILIARY CONTROL PANEL

The auxiliary control panel, conveniently located in the spa seating surface area (Vista®, Grandee®, Envoy®, Vanguard®, Sovereign®, Aria™, and Prodigy® models) allows the user to actuate the jets, light, and Spaudio® functions from inside the spa. If in that location is a trouble with the AUXILIARY CONTROL PANEL it will be unresponsive, please then BOOK A SERVICE CALL with us.

INDICATOR LIGHTS

At a glance, the indicator lights are readily visible on the main control panel.

The 3 indicator lights: POWER, READY and CLEAN, piece of work independently from the residuum of the control panel display. That way, even if the command console is off, yous can simply glance at the "Prepare" indicator light to determine whether or not your spa is within the range of your prepare temperature.

• Power Indicator: The POWER indicator is 'on' when the spa is properly supplied with power. It also provides a diagnostic function–a blinking ability indicator indicates that the heater high limit has tripped, meaning that either the spa water is higher up its acceptable temperature range, or a malfunction has occurred within the spa (such equally low circulation due to clogged filters). An 'off' power indicator means that there is a problem with the spa control box or the power supplied to the spa.
• Ready Indicator: The READY indicator will light when the spa water temperature is within 2-1/2°F (1.4°C) of the set temperature, and will turn off when the temperature is outside of that range. If yous increase or decrease the temperature setting of the spa, the prepare indicator will plough off until the spa temperature reaches the acceptable range for the new gear up temperature. Additionally, a blinking Ready indicator indicates that a problem exists with the temperature sensor.
• Clean Indicator: The CLEAN indicator lights upward when the CLEAN button is pressed. Information technology remains on during the ten-minute clean cycle (used for h2o maintenance), then automatically shuts off at the end of the bike. The JET symbol will also illuminate on the brandish to indicate that the jet pump is on.

LOCKING FEATURES

The two locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the main control panel past pressing a specific combination of buttons. Once enabled, a lock will remain active until the specific push button combination is practical to disable the lock. Even if power is disconnected from the spa and soon thereafter reapplied (such as in a power outage) the lock will remain in place.

SPA LOCK

The SPA LOCK characteristic deactivates all of the functions of the main and auxiliary control panels. Information technology is generally used to foreclose unwanted use of the spa. To activate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-) buttons at the same fourth dimension and hold them down until the word SPA and the lock symbol are illuminated on the display (approximately ii seconds). When the SPA LOCK is activated, if a button is pressed, the control panel volition display the lock symbol and the give-and-take SPA for 30 seconds, so plow off. To conciliate the SPA LOCK, press the Calorie-free minus (-) and TEMP minus (-) buttons at the aforementioned fourth dimension and concord them down until the give-and-take SPA and the lock symbol are no longer illuminated on the brandish (approximately two seconds).

TEMPERATURE LOCK

The TEMPERATURE LOCK feature deactivates the temperature control role of the principal control panel. All other functions on the main and auxiliary control panels will operate normally. TEMPERATURE LOCK is almost often used by people who do not want others to tamper with or change the fix temperature of the spa water. To activate the TEMPERATURE LOCK, press the LIGHT plus (+) and TEMP plus (+) buttons at the same time and hold them downward until the words Set up TEMP, the numerical set temperature value and the lock symbol are illuminated on the display (approximately 2 seconds).

When the TEMPERATURE LOCK is activated, the JETS, LIGHT, and Make clean buttons will operate normally, and the temperature setting tin can be viewed simply can NOT be inverse. If a temperature button is pressed, the control panel will display the lock symbol and the set up temperature for xxx seconds, then turn off. To deactivate the TEMPERATURE LOCK, press the Lite plus (+) and TEMP plus (+) buttons at the same time and hold them down until the lock symbol is no longer illuminated on the display (approximately two seconds).

Chief Command PANEL BUTTONS & DISPLAY

The primary control panel has buttons which the spa user presses to fix the temperature, initiate the clean cycle, vary the intensity of the light, and activate or deactivate the jet pump. With the exception of the CLEAN button, the control panel display responds to let you know you've pressed a button, and that the selected function has been performed. After a period of non-use, pressing any button will wake upwardly a sleeping display, likewise as performing its function.

TEMPERATURE CONTROL

The set temperature range is from 80°F to 104°F (27°C to 40°C). (The temperature of any setting may ascension slightly depending on the electric current use and status of your spa, and on outside temperatures.) The set temperature of the spa water will automatically be 102°F (39°C) the first time that power is applied. This is the setting programmed at the factory. After the spa has been set up and used, the final temperature value ready past the user will exist stored in retentiveness. If power is disconnected from the spa, information technology will automatically revert to the last ready temperature when power is reapplied. To display the fix temperature of the spa, press the TEMP plus (+) button. The ready temperature will be displayed, unless the spa is locked (in which case the discussion SPA is displayed with the lock symbol). The ready temperature display will automatically shut off later thirty seconds.

To increase the set up temperature of the spa h2o, press the TEMP plus (+) push. Each fourth dimension the push button is pressed, the set temperature brandish volition increment by one caste. If the button is held down, the set temperature display will increase by one degree every half-2d. To decrease the prepare temperature of the spa water, press the TEMP minus (-) button. Each time the button is pressed, the fix temperature display will decrement by one caste. If the push is held down, the ready temperature brandish volition decrease by one degree every half-2nd. If the set temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features is applied, the temperature control is disabled.

JETS CONTROL

There are 2 buttons (three buttons on Vista® ,Grandee®, Envoy®, Aria™ and Vanguard® models) which affect the jet pump(s):The JETS push (all models) / JETS i (Vista, Grandee, Envoy, Aria and Vanguard models just) activates the jet pump.

• When the JETS or JETS one button is pressed, the jets symbol will illuminate on the control panel display. The symbol will remain lit until the push is pressed to turn off the jet pump, or afterward ii hours of continuous operation when the pump is automatically shut off past the control system.
• The JETS 2 button (Vista, Grandee, Envoy, Aria and Vanguard only) activates the second jet pump. When the JETS ii button is pressed, the jets symbol will illuminate on the control panel display. (Vista, Envoy & Aria will run in low speed with first printing and high speed with 2nd press). The symbol will remain lit until the button is pressed to turn off the jet pump, or subsequently two hours of continuous performance when the pump is automatically shut off by the control system.
• The CLEAN push button, provided as a user-friendly timer for water maintenance, activates the jet pump for a x minute period. The Make clean indicator will turn on and the JET symbol on the brandish will illuminate to point the jet pump is engaged.

Adjacent, you may add together properly measured spa h2o chemicals into the filter compartment. The jet pump and clean indicator volition automatically shut off after ten minutes. If the jet pump will not appoint, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panels.

LIGHT CONTROL- STANDARD

The intensity of the spa's light is controlled using the LIGHT plus (+) or Light minus (-) buttons. To turn on the spa low-cal, press the LIGHT plus (+) button. The light volition turn on at maximum intensity and the calorie-free symbol will illuminate on the control panel display. To reduce the intensity of the light, press the LIGHT minus (-) button. The intensity of the lite will decrease each time the button is pressed. Additionally, if either of the Calorie-free buttons (+ or -) on the Chief Control console only, are held down, the low-cal intensity will increase or subtract at the rate of 1 intensity level every half-second.

To turn off the light, hold the LIGHT minus (-) button. The light will dim and turn off. When the calorie-free turns off, the low-cal symbol on the display volition as well turn off. If the light is left on, information technology will automatically be turned off by the control organisation after half dozen hours of continuous performance. The light symbol on the panel will also turn off when the light is deactivated. If the calorie-free volition not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panels.

Calorie-free CONTROL- LUMINESCENCE

All Hot Spring spas are equipped with the Luminescence (Multi-Color) low-cal. The intensity of the spa's light is controlled using the Calorie-free Plus (+) or Calorie-free Minus (-) buttons. In that location are 5 (v) brightness levels plus off. To plough on the spa calorie-free, press the LIGHT Plus (+) push button. The low-cal will plow on at maximum intensity and the light symbol will illuminate on the control panel display. When the lite is set to its maximum brightness setting, printing the LIGHT Plus (+) push button to modify the color. The color loop sequence is set up equally follows: Blueish, Aqua, Green, White, Bister, Crimson, Loop ON, Loop OFF. To activate the color loop, press (+) after the color red. The colors will automatically run through the sequence in the society listed higher up. To stop the loop press the Light Plus (+) button while the loop is on and the brightness setting is in the maximum position. To reduce the intensity of the low-cal, press the LIGHT Minus (-) button.

 The intensity of the low-cal will subtract each time the push is pressed. Additionally, if the Lite Minus (-) push button on the Main Control panel only, is held downwards, the low-cal intensity will decrease at the rate of one intensity level every half-second until information technology shuts off. If the intensity of lite is below the maximum effulgence and the LIGHT Plus (+) push is pressed and held down, the lite will increment intensity until it reaches maximum effulgence, it volition then proceed through the color sequence every half-2nd until the push is released. To turn off the light, hold the Light Minus (-) button. The light volition dim and turn off. When the light turns off, the light symbol on the display will also turn off. If the light is left on, it will automatically be turned off by the control arrangement afterwards 6 hours of continuous operation. The calorie-free symbol on the panel will also turn off when the lite is deactivated. If the calorie-free will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panels.

Summer MODE Brandish

The Summer Manner symbol is on when the Summer Style timer is on. When activated, the symbol will be visible even in bright light when the principal display backlight is off. In low light weather condition, the Summertime Mode symbol volition only be visible when the display is activated past pressing a control panel button.

Your Hot Jump spa is equipped with a Summer Way timer. The Summer Style timer can be activated during extremely hot summer months if it becomes difficult to maintain h2o temperatures depression enough for comfort. Upon switching to the ON mode, the heater will immediately shut downward while the circulation pump (which can add together oestrus to the water through normal functioning) will remain on for approximately 5 minutes for heater absurd down. Both heater and apportionment pump will remain off for the next eight hours.

Additionally, the summertime manner display on the main command panel volition activate and remain agile for as long as the summer mode is on. Post-obit this viii-60 minutes period, the circulation pump and heater volition automatically restart and will operate commonly for the next sixteen hours. The circulation pump and heater will continue to turn off for an eight-hour period every twenty-four hours that the switch remains in the ON position. In this way, the amount of heat transferred to the spa water will be minimized. When the exterior temperatures begin to absurd, the Summer Mode timer should be turned to the OFF position (the summer mode display on the main command panel volition become out). This is the efficient 24 60 minutes circulation mode that keeps the heater performance and operating costs to a minimum during colder/heavier usage months.

Please note that whenever power is disconnected and and so reconnected to the spa, the Summer Mode timer will reset starting with the eight-60 minutes shutdown mode. If a dissimilar eight-hour shut down time is desired, conciliate the Summer Mode, then reactivate at the showtime of the desired eight-hour shut down time. The Summer Mode volition non lower the spa's h2o temperature below the ambient air temperature.

To actuate the Summer Fashion, but follow these steps:

• Set the temperature control to 80°F (26°C).
• On the command panel, simultaneously printing and hold for iii seconds Temp Plus and Temp Minus buttons to activate the Summertime Timer. The Summertime Style must be deactivated when cooler temperatures return.
• To do this, just echo step ii.
• Please exist aware that failure to deactivate the Summer Manner when the temperature drops beneath 32°F (0°C) will result in freezing of the spa. Damage resulting from this situation is not covered nether the terms of the warranty.

If you take whatever further questions or require further assist, please volume a Hot Tub Service with usa.

Book A HOT TUB SERVICE

Source: https://www.pioneerfamilypools.ca/advice/hotspring-spas-locks-trouble-shooting/

Share this post